SaraNextGen.Com
Updated By SaraNextGen
On March 11, 2024, 11:35 AM

Page No 222: - Chapter 12 Electricity class 10 ncert solutions Science - SaraNextGen [2024]


Question 15:

Two lamps, one rated 100 W at 220 V, and the other 60 W at 220 V, are connected in parallel to electric mains supply. What current is drawn from the line if the supply voltage is 220 V?

Answer:

Both the bulbs are connected in parallel. Therefore, potential difference across each of them will be 220 V, because no division of voltage occurs in a parallel circuit.

Current drawn by the bulb of rating 100 W is given by,

https://img-nm.mnimgs.com/img/study_content/curr/1/10/10/156/1227/Chapter%2012_html_m1ca5e5.gif

Similarly, current drawn by the bulb of rating 60 W is given by,

https://img-nm.mnimgs.com/img/study_content/curr/1/10/10/156/1227/Chapter%2012_html_75c3747.gif

https://img-nm.mnimgs.com/img/study_content/curr/1/10/10/156/1227/Chapter%2012_html_71d2bc29.gif

Question 16:

Which uses more energy, a 250 W TV set in 1 hr, or a 1200 W toaster in 10 minutes?

Answer:

Energy consumed by an electrical appliance is given by the expression,

https://img-nm.mnimgs.com/img/study_content/curr/1/10/10/156/1230/Chapter%2012_html_694b94f0.gif

Where,

Power of the appliance = P

Time = t

Energy consumed by a TV set of power 250 W in 1 h = 250 × 3600 = 9 × 105 J

Energy consumed by a toaster of power 1200 W in 10 minutes = 1200 × 600

= 7.2× 105 J

Therefore, the energy consumed by a 250 W TV set in 1 h is more than the energy consumed by a toaster of power 1200 W in 10 minutes.

Question 17:

An electric heater of resistance 8 Ω draws 15 A from the service mains 2 hours. Calculate the rate at which heat is developed in the heater.

Answer:

Rate of heat produced by a device is given by the expression for power as

https://img-nm.mnimgs.com/img/study_content/curr/1/10/10/156/1234/Chapter%2012_html_m52cdfd4c.gif

Where,

Resistance of the electric heater, R = 8 Ω

Current drawn, = 15 A

https://img-nm.mnimgs.com/img/study_content/curr/1/10/10/156/1234/Chapter%2012_html_m96880e7.gif

Therefore, heat is produced by the heater at the rate of 1800 J/s.

Question 18:

Explain the following.

(a) Why is the tungsten used almost exclusively for filament of electric lamps?

(b) Why are the conductors of electric heating devices, such as bread-toasters and electric irons, made of an alloy rather than a pure metal?

(c) Why is the series arrangement not used for domestic circuits?

(d) How does the resistance of a wire vary with its area of cross-section?

(e) Why are copper and aluminium wires usually employed for electricity transmission?

Answer:

(a) The melting point and resistivity of tungsten are very high. It does not burn readily at a high temperature. The electric lamps glow at very high temperatures. Hence, tungsten is mainly used as heating element of electric bulbs.

(b) The conductors of electric heating devices such as bread toasters and electric irons are made of alloy because resistivity of an alloy is more than that of metals. It produces large amount of heat.

(c) There is voltage division in series circuits. Each component of a series circuit receives a small voltage for a large supply voltage. As a result, the amount of current decreases and the device becomes hot. Hence, series arrangement is not used in domestic circuits.

(d) Resistance (R) of a wire is inversely proportional to its area of cross-section (A), i.e.,

https://img-nm.mnimgs.com/img/study_content/curr/1/10/10/156/1238/Chapter%2012_html_89c5c64.gif

(e) Copper and aluminium wires have low resistivity. They are good conductors of electricity. Hence, they are usually employed for electricity transmission.

Also Read : INTRODUCTION-Chapter-14-Sources-&-Energy-class-10-ncert-solutions-Science

SaraNextGen